Possible Faults With Your 12V Battery





0
Date Submitted Mon. Feb. 27th, 2017 2:31 AM
Revision 1 of 1
Syntax Master autosuma
Tags Autel | MaxiSys | Mini | ms905 | ms906
Comments 0 comments
Something wrong with your battery, find out what kind of fault it is;

Battery problems - Manufacturing Faults

Short circuit/dead cell
Typically seen in a battery with a short (less than 12 months) service life. One cell will show a dramatically lower specific gravity (SG) reading than the others. The affected cell will boil visibly under a high rate discharge test. In some cases it may also be visible as a sulphated cell.
The remaining cells will show a good SG reading of 1.26 or over.

Internal Break
The battery will have good SG readings but no voltage.

Summary
Provided the right battery, in the right condition is used for the right application, the number of battery problems encountered will be minimum. All batteries have a finite life span, which is governed by the conditions under which the battery operates. Battery failures caused by sulphation, wear and tear, or deep cycling are not manufacturing faults and are not covered by the manufacturer.

Battery problems - Non-manufacturing faults

Sulphation
If a battery is allowed to stand in a discharged state for an excessive amount of time, a chemical reaction takes place, which can permanently impair performance - this is sulphation. Sulphation can be seen as a fine white/grey coating on the plates. In most cases this signifies irreversible damage and the battery will not be serviceable. This damage can occur either in storage or if the battery is installed in a vehicle (or equipment) that is not used for a period of time, for example a tractor, motorcycle, or boat. Even a car or truck that is stored with the battery connected can still damage the battery in this way. This is because there is a permanent drain on the battery from the clock, alarm etc. As a result the level of charge in a battery falls, and after a period of time sulphation will build up on the plates. The sulphation (lead sulphate) hinders the chemical reaction between the acid (electrolyte) and the active mass (lead compound) in the plates and prevents the battery from operating as normal. This is not a manufacturing fault.

Incorrect application
The batteries recommended are those equal to or above the original equipment specification. Fitting a smaller or less powerful battery will result in a shorter service life and earlier failure, which will generally manifest itself as deep cycling/premature wear and tear. This is not a manufacturing fault.


Wear and Tear
During the charge and discharge cycle, material from the battery plates (active mass) is in motion, through the electrochemical reaction that produces electricity autel maxisys ms906. Every time the battery goes through a charge and discharge cycle, a small amount of the active mass is lost from the plates. Because the ultimate life of a battery depends on so many factors, it is impossible to stipulate a minimum/maximum life expectancy. This process of normal ageing through the charge and discharge cycle will eventually cause the battery to lose capacity, and it will come to the point where the battery can no longer start the vehicle/equipment. This is not a manufacturing fault.

A battery only has a finite number of cycles (x) it can go through before it loses its capacity to perform. Vehicles with high usage such as taxi's, minicabs, trucks, and buses will often subject the battery to its x number of cycles but over a much shorter time. As a result, batteries on these vehicles can display the above symptoms after 12-24 months. This is not a manufacturing fault.

Deep cycling
As mentioned above, every time a battery goes through a charge and discharge cycle a small amount of the material from the plates is lost. If a battery is subjected to deep discharging (i.e. over 40%) and then rapid charging, this process is accelerated. Additionally, if during the recharge the battery is not adequately compensated for the discharge cycle, the battery will quickly exhibit loss of performance. Even after recharging the voltage will be low (under 12.4v) but the cells will generally give even readings. This is not a manufacturing fault.

Overcharging
If the regulator is not set properly, then the battery can be subjected to an excessive charge. If left unchecked the battery will overheat and will start to evaporate the electrolyte. The overcharging will cause the accelerated breakup of the active mass on the plates and the battery will lose performance. This is generally obvious from the examination of the battery - the acid levels will be very low, and quite often a black coating will be visible on the filler caps. This is not a manufacturing fault.

Physical damage

If the battery is fitted incorrectly, if the connector leads are hammered onto the terminals, or if the leads are not properly fastened, the battery will have obvious damage to the casing or the terminals.
This is not a manufacturing fault.


Any questions? Feel free to ask in the comments below.

Disclaimer: This information supplied is for general information with regards to looking after your new battery only, Please exercise caution when you are handling and using batteries autel maxisys mini ms905. If you feel your experience is inadequate please obtain professional help. Lake Renewable Energy/ Lake Batteries assumes no responsibility and liabilities for the damages and accidents involved in handling batteries by you the customer.
Require help regarding the information supplied or additional product information please contact our customer service dept.


Related Links http://www.autelonline.com


...

 

auto suma

Comments

There are currently no comments for this snippet.

Voting

Votes Up


Votes Down